Restoration of GPA 7757

Here you can post your GPA serial numbers, your GPA history and if you want
some owners info with pictures.
Nice to see a face that belongs to a GPA !

Moderator: bobassel

bobassel
Site Admin
Site Admin
Posts: 461
Joined: Mon Dec 12, 2005 10:29 pm
Contact:

Re: Restoration of GPA 7757

Post by bobassel » Mon Aug 13, 2018 10:52 am

Hi John,

Good to hear from you, and you are working on the project.
If you having troubles with the pictures, just mail them to me, and I will place them.
Photo's make it more interesting.
Regards, Bob
Ford GPA 12350, april 4th 1943
Author of GPA book,
Willys MD M38A1, A13817 1952

john4172
Posts: 18
Joined: Fri Jul 02, 2010 12:32 am
Contact:

Re: Restoration of GPA 7757

Post by john4172 » Sat Oct 06, 2018 10:57 am

V Seals. In Bobs very useful book he mentioned V seals to assist the wheel seals. I was able to buy 4 over the counter at Griffith 100 km away . I have since bought 3 vs 25 and will fit as follows. One to seal the steering box where the shaft goes in, and one each side of the prop shaft bearing to keep sand out of the bearing and the grease in!.
The estimated return date for the hull is now January. It will take a lot of work to get it to Corowa 2019 in Mach.I will give it a go.
John Mackie
- GPA 7757 D.O.D 2-16-43
- GPW 11798 D.O.D 4-14-42
- White M3A1
- LP2A 4172
- Ford 01T Trucks X 3

john4172
Posts: 18
Joined: Fri Jul 02, 2010 12:32 am
Contact:

Re: Restoration of GPA 7757

Post by john4172 » Sun Feb 03, 2019 9:42 am

Hullo All.My appologys for bieng absent from the site for so long. Over the last few days I seem to have made some progress. I have moved the engine, gearbox and transker case to the back of my truck.the engine has been started and run with some troublea with a blockage in the new fuel pump and dried out washers in the carby. The engine now has about 2 hours on it. the head has been re-tightened and the tappets checked. I have hooked up the gene and the regulator. I had difficulty gatting it to charge, the comutatior and the brushes were not good even though it was overhauled before it was put away. Itis now charging now but needs more tension on the brush springs. The brushes are 90% good. This is a job for tomorrow.
There is no definite word about the return of the hull and as Corowa swim in is not only 5 weeks away it will take a lot of work to ger it there. I still have to make brake and fuel lines,clutch relay lever, drag link after the engine is in the hull.
I will try to post more details as it happens
John Mackie
- GPA 7757 D.O.D 2-16-43
- GPW 11798 D.O.D 4-14-42
- White M3A1
- LP2A 4172
- Ford 01T Trucks X 3

john4172
Posts: 18
Joined: Fri Jul 02, 2010 12:32 am
Contact:

Re: Restoration of GPA 7757

Post by john4172 » Wed Nov 20, 2019 9:51 am

Hullo all, here is an update on progress. The hull has been back fron Simon Allen for a couple of momths, all seams have been sealed with sickaflex, the interior and underneath painted. The fuel and brake pipes have been made, The chassis is now in the hull all shackle brackets , bump rubbers and shock bolts are in and sealed. Theprop shaft , thrust bearing crank device are installed and adjusted. I hope to have the axles and springs and on it's wheels by Christmas.
I have photos but need a hand to post them.
John Mackie
- GPA 7757 D.O.D 2-16-43
- GPW 11798 D.O.D 4-14-42
- White M3A1
- LP2A 4172
- Ford 01T Trucks X 3

bobassel
Site Admin
Site Admin
Posts: 461
Joined: Mon Dec 12, 2005 10:29 pm
Contact:

Re: Restoration of GPA 7757

Post by bobassel » Sun Dec 01, 2019 4:21 pm

Hi John,
Yes pictures please!
If you send them to me, I can place them for you .

Bob
Ford GPA 12350, april 4th 1943
Author of GPA book,
Willys MD M38A1, A13817 1952

john4172
Posts: 18
Joined: Fri Jul 02, 2010 12:32 am
Contact:

Re: Restoration of GPA 7757

Post by john4172 » Mon Jun 22, 2020 12:32 am

Hi all. My appologys it is 6 months since I have updated this post. I recently had a week working on the GPA. I now have the air ducts,some bilge pipes installed, I left the long one behind! Will fix that next trip, soon i hope. John (son) wants to put on another coat of paint on and also cover everything with fish oil. After that I want to get the axles fitted.

One query that I have is what is the differencebetween GPA 3590 and GPW 3590 pitman arms ?
I have had made the 2 ends for the drag link ( 3304 ) they each have a 3/4 UNF female thread and will be joined by a length of 3/4 dianater stainless plated hydraulic ram rod, this will save having to squese the ends through the boot.

Moore and photos later.
John Mackie
- GPA 7757 D.O.D 2-16-43
- GPW 11798 D.O.D 4-14-42
- White M3A1
- LP2A 4172
- Ford 01T Trucks X 3

Amphibian
Posts: 8
Joined: Mon Apr 27, 2020 5:23 am
Contact:

Re: Restoration of GPA 7757

Post by Amphibian » Tue Jun 23, 2020 9:01 am

Hi John,good to see you are getting there with your GPA.Ive got some photos of the Pitman Arm for you to view.Ill send them via Bob ,as I still am unable to attach images.regards Rick

bobassel
Site Admin
Site Admin
Posts: 461
Joined: Mon Dec 12, 2005 10:29 pm
Contact:

Re: Restoration of GPA 7757

Post by bobassel » Tue Jun 23, 2020 6:36 pm

Hi John,
I operate as the speaksmen from Rick lol
He asked me to put some pictures on the forum for your question.
As you can see, the angle is different from the GPW version.
You need this because otherwise you will have a problem with fitting the engine.
Image
Image
I hope this helps.
All the best from Rick & Bob
Ford GPA 12350, april 4th 1943
Author of GPA book,
Willys MD M38A1, A13817 1952

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests